Film speed: ASA, DIN, ISO and EI¶
On a digital camera, “ISO” is a setting you turn up in the dark. On film it is the opposite: a fixed, measured property of the emulsion, printed on the box because the manufacturer determined it in a lab to an international standard. Understanding what that number is tells you a lot about how to expose.
In short
Film speed = how much light the film needs for a proper exposure. Higher number = less light needed = “faster”.
The scale is defined so that doubling the number = one stop = half the light. ISO 400 needs exactly half the light of ISO 200.
ASA (American) and DIN (German) were the two old standards. Modern ISO speed is literally the two of them printed together:
ISO 400/27°. The plain number everyone quotes is the old ASA number.The ISO number is fixed by a standard test (ISO 6:1993 for B&W, ISO 5800 for colour negative, ISO 2240 for reversal) that measures the film’s real sensitivity.
Exposure Index (EI) is the speed you choose to shoot it at, which may differ on purpose – that is pushing or pulling.
What “needs less light” means physically¶
A faster film is faster because its silver-halide crystals are, on average, bigger, and/or shaped and chemically sensitised to catch photons more efficiently. A bigger crystal is a bigger target and needs fewer photons to accumulate a stable latent-image speck (see Silver halide: the light-sensitive heart of film).
That is why speed and grain trade off: the property that makes ISO 3200 film fast – large crystals – is the same property that makes it grainy. You cannot have fast, fine, and cheap all at once; film design is the art of choosing which to give up.
There’s no free lunch
Every stop of extra film speed costs you something – grain, sharpness, or exposure latitude. When a modern ISO 400 film looks nearly as clean as an ISO 100 film from the 1980s, that is 40 years of crystal engineering (T-grain, better sensitisation) buying back the penalty, not repealing the rule.
The old scales¶
ASA (American Standards Association, 1943 onward)¶
An arithmetic scale: linear in sensitivity. ASA 200 is twice as sensitive as ASA 100. A 1960 revision removed a built-in safety factor and effectively doubled all the numbers – an ASA 100 film after 1960 is the same as an ASA 50 film before it, which is a trap when reading very old exposure guides and meters.
DIN (Deutsches Institut für Normung, 1934 onward)¶
A logarithmic scale, written with a degree sign: +3° DIN = one stop = double the speed. Common values:
DIN |
15° |
18° |
21° |
24° |
|---|---|---|---|---|
≈ ASA |
25 |
50 |
100 |
200 |
You still meet DIN on old German cameras and light meters (Praktica, early Leica dials) and in the second half of the modern ISO designation.
GOST (СССР / Soviet, ГОСТ)¶
The Soviet arithmetic standard, close to ASA but not identical – pre-1987 GOST was about 0.9× the ASA value (GOST 65 ≈ ASA 64/72). Post-1987 GOST was harmonised to ISO. Relevant if you shoot a Zenit or old Svema/Tasma film.
Modern ISO speed¶
ISO fused ASA and DIN into one designation. The correct full form is:
ISO 400/27°
The first number (
400) is the arithmetic speed – identical to the old ASA value.The second (
27°) is the logarithmic speed – identical to the old DIN value.
In everyday use everyone drops the logarithmic half and says “ISO 400”. Camera dials, DX codes and databacks use only the arithmetic number.
How the number is actually determined¶
It is not marketing. Each film type has a test method:
ISO 6 – black-and-white negative. The film is given a series of exposures and developed to a specified contrast (a fixed gradient). The speed point is the exposure that produces a density of 0.10 above base+fog. Speed
S = 0.8 / H_m, whereH_mis that exposure in lux-seconds. In plain terms: the least light that lifts the shadows just off the film’s floor.ISO 5800 – colour negative. Similar idea but measured on all three colour layers, with the speed point defined from the average of the slowest layers.
ISO 2240 – colour reversal. Measured from the highlight end instead – the exposure that gives a density a set amount above the minimum (clear film). Slide film is speed-rated to protect highlights, which is exactly why you meter it differently.
Jargon buster
base + fog (b+f) – the density of a piece of film that was developed but never exposed: the tint of the base plus a few crystals that developed spontaneously. It is the film’s darkest-possible clear area and the zero point for every speed and curve measurement.
lux-second (lx·s) – illuminance × time. The natural unit of photographic exposure
(H). One stop = a factor of two in lux-seconds.
Why film ISO is not a dial¶
When you “set the ISO” on a film camera you are not changing the film. You are telling the light meter which film is loaded so it recommends the right aperture and shutter speed. The film’s sensitivity is fixed the moment it was manufactured.
This has three consequences:
One roll, one speed. You cannot shoot frame 12 at ISO 100 and frame 13 at ISO 800 and have both come out normally, because they all get the same development. (You can change your mind for the whole roll – see push/pull below.)
The camera’s ISO dial can be used deliberately “wrong” to rate the film at a different EI – e.g. setting ISO 200 with HP5 Plus (nominally 400) loaded, so every frame gets one extra stop of light.
DX-coded auto-ISO cameras read the film speed from the chequered pattern on the cassette and may not let you override it. A strip of tape over two contacts is the classic fix.
Exposure Index (EI): the speed you choose¶
EI is the ISO you pretend the film has. If the box says ISO 400 but you set your meter to 800 and shoot the whole roll that way, you are shooting at EI 800. Every frame is then underexposed by one stop relative to the box speed, and you compensate by telling the lab to push development (extra time in the developer) to build the shadows and midtones back up.
You set the meter to… |
vs box speed |
Development |
Why you’d do it |
|---|---|---|---|
EI = box ISO |
normal |
normal (“box speed”) |
The default. What the film was designed for. |
EI higher (e.g. 400→1600) |
underexpose |
push +1, +2 stops |
Need a faster shutter / smaller aperture in low light; accept more grain and contrast, crushed shadows. |
EI lower (e.g. 400→200) |
overexpose |
pull −1 stop (or normal) |
Tame contrast in harsh light, get richer shadows, finer apparent grain. Common practice with colour negative (“overexpose and print down”). |
Fun fact
Many photographers habitually rate colour negative film ⅔–1 stop slower than the box – Portra 400 at EI 200–320, Gold 200 at EI 100–160 – and develop normally. Colour negative film holds highlights extremely well but shows noise and colour shifts in underexposed shadows, so “when in doubt, give it more light” is close to a universal rule. Slide film is the reverse: rate it at box speed or very slightly faster, because its highlights blow out abruptly.
Reading the box and the cassette¶
Marking |
Meaning |
|---|---|
|
Full modern designation. Arithmetic 400, logarithmic 27. |
|
The speed you dial into your meter. |
|
Machine-readable code: film speed, number of exposures, exposure latitude. Cameras with DX contacts read speed automatically. |
|
Old German-market notation; convert with +3°/stop. |
|
Old Soviet notation; ≈ ISO 100. |
|
The process, not the speed – which chemistry the lab must use. |
Common mistake
“ISO 800 film is just ISO 400 film pushed a stop.” No. A true ISO 800 film (Portra 800, CineStill 800T) is a different emulsion, engineered with larger or better-sensitised crystals to genuinely meter that fast with normal development. Pushing ISO 400 film to 800 gives you more contrast, bigger grain and thinner shadows than a native ISO 800 film shot at box speed. Sometimes that look is what you want – but they are not the same thing.
Where to go next
Exposure on film – putting the speed number to work with aperture and shutter.
Pushing and pulling film – the full mechanics of shooting off box speed.
Grain, granularity and sharpness – why fast film is grainy.