Metering and exposure in practice¶
Exposure on film covered the theory. This is the field manual: how to get a correctly exposed frame with the meter you actually have.
In short
Your camera meter reads reflected light and assumes the world averages to middle grey. It is fooled by snow, beaches, spotlights, dark subjects and backlight.
Incident metering (handheld, white dome at the subject) ignores subject reflectance and is the most reliable for portraits and controlled light.
Negative film: bias toward overexposure. Slide film: bias toward (slight) underexposure. This falls straight out of the curve shapes.
The Zone System is just “decide which tone you want a spot-metered area to become, then set exposure so it lands there.”
What “middle grey” means and why it matters¶
A reflected-light meter (in-camera, or a handheld in reflected mode) has no idea what it’s looking at. It assumes the scene’s average reflectance is ~12–18% – a mid grey – and picks an exposure to render whatever it sees as that grey.
Point it at a snowfield → it renders the snow mid-grey → your snow is underexposed by ~2 stops (dull grey slush).
Point it at a black cat on coal → it renders the black mid-grey → overexposed, a grey cat.
Backlit portrait → meter sees the bright background, stops down, face goes dark.
The fixes:
Technique |
How |
|---|---|
Meter a grey card |
Fill the frame (or spot) with an 18% grey card in the subject’s light; use that reading. The reference method. |
Meter your palm, +1 stop |
Caucasian palm ≈ 1 stop brighter than grey; darker skin ≈ +⅔ to +1½. Meter the back of your hand in the subject light and open up ~1 stop. |
Incident meter |
Stand at the subject, dome pointed back at the camera/light, read directly. No reflectance guessing. |
Expose to the right tone deliberately |
Spot-meter a known tone and offset: “this white wall should be +2 stops” → meter it, add 2 stops. |
Sunny 16 sanity check |
Bright sun = 1/ISO at f/16. If your meter disagrees wildly, something’s fooling it. |
The three meter types¶
Meter |
Reads |
Best for |
|---|---|---|
Reflected (in-camera, averaging / centre-weighted / matrix) |
light bouncing off the scene |
general shooting, quick work; trust it in even light, override it in tricky light |
Spot (1–5°) |
a tiny patch of the scene |
deliberate tone placement, high-contrast scenes, the Zone System, slide film |
Incident (handheld, dome) |
light falling on the subject |
portraits, studio, film sets, anything where you can reach the subject; the most consistent |
Fun fact
The “18%” figure is a bit of a myth. Kodak’s grey cards are 18% reflectance, but most camera meters are actually calibrated closer to 12–13% (an ANSI standard constant), about ⅓–½ stop apart. It rarely matters for negative film’s latitude, but it’s why careful slide shooters calibrate their own EI by testing rather than trusting the box.
Metering by film type – recipes¶
Colour negative¶
Goal: keep shadows off the toe. Overexposure is nearly free.
Set the meter ⅔–1 stop below box speed (Portra 400 → EI 250–320, Gold 200 → EI 125) and shoot normally. This is the single most common pro habit.
Or meter the shadow you want to keep detail in and place it ~2 stops below mid-grey (i.e. meter it, then close down 2 stops from that reading… no – open up: meter the shadow, it wants to make it grey, you want it dark-but-detailed, so give −2 from the shadow reading = shadow sits 2 stops under grey).
In flat light you can shoot box speed and be fine.
Backlight / window light: add 1–2 stops over the meter.
Colour slide (E-6)¶
Goal: protect highlights. You have ±½ stop.
Incident meter, shoot the reading, bracket ±⅓ for anything critical.
Spot method: meter the brightest important highlight (textured white, bright cloud, lit skin) and place it +2 stops over mid-grey. Anything brighter will clip – accept it.
Rate at box speed, or test and settle on EI 40 (Velvia 50), EI 100, etc.
In contrasty light, decide what you’re willing to lose (usually the shadows).
Black-and-white negative¶
Goal: expose for the shadows, develop for the highlights (Zone System in one line).
Rate ⅓–⅔ slow for traditional films (HP5+ → EI 250–320, Tri-X → EI 250, FP4+ → EI 100) to guarantee shadow detail.
Spot-meter the darkest area you want texture in and place it on Zone III (meter reading −2 stops).
Then check where the important highlights land; if they’re above Zone VIII, plan to reduce development (“N−1”); if the scene is flat and highlights only reach Zone VI, increase development (“N+1”). See Pushing and pulling film.
The Zone System, briefly¶
Ansel Adams and Fred Archer’s system is the characteristic curve turned into a field workflow. Tones are numbered 0 (max black) to X (paper white), each Zone = one stop, Zone V = middle grey = what the meter gives you.
Zone |
Tone |
Use |
|---|---|---|
0 / I |
full black / near-black, no texture |
deepest shadow |
III |
dark, textured (dark fabric, shadow detail) |
place your important shadow here (meter −2 stops) |
V |
middle grey |
the meter’s default; dark skin, weathered wood, blue sky |
VI |
light, textured (average Caucasian skin) |
common portrait placement (meter +1) |
VIII |
textured white (snow in sun, white shirt) |
highest zone that still holds detail |
IX / X |
white, no texture / paper base |
specular highlights, light sources |
Workflow: spot-meter the shadow → decide its Zone → that sets exposure. Spot-meter the highlight → see which Zone it falls on → that sets development. “Expose for the shadows, develop for the highlights.”
For roll film (can’t develop frame-by-frame) you pick an average development and accept that very contrasty or very flat frames on the roll won’t be ideal – or you dedicate a roll to one lighting situation.
Where to go next
Pushing and pulling film – the “develop for the highlights” half.
Latitude, contrast and dynamic range – how much error each film really forgives.
Filters for film – filters change your metering; here’s how much.